TopMax III High-Speed Universal Device Programmer The TopMax-III is a high-speed universal device programmer for USB 1.1/2.0/3.0 PC-interface. It can program a 64Mbit (AM29LV641) flash memory in 42 seconds. This is a true low-cost production-oriented system. The TopMax-III meets the demands of today's programming solution for lab and production on line applications. TopMax-III is a software driven device programmer that supports a wide variety of programmable devices including: EPROM, EEPROM, Serial PROM, EPLD, PEEL, GAL, FPGA, and single chip Microcontroller. The great advantage of this programmer is its programming speed and superior software. It's controlled via a host IBM PC or compatible computer, and the operating software has a user-friendly interface that includes window pull-down menus and virtual memory management to deal with very large files. Hardware Features One on-board FPGAs for extremely fast communication. Extremely fast SPI, QPI Serial memory support Supports real low-voltage such as 5, 3.3, 2.7, 1.8 volts for programming power Detects all pin locations for poor or damaged pin contacts External START Key allows production programming mode Internal universal power supply, 110-240 VAC (no separate power supply required in foreign country) Current limiting protects hardware circuit from improperly inserted or defective chips and operation errors Standard 48-pin ZIF (Zero Insertion Force) socket accepts both 300mil and 600 mil DIP devices True universal pin driver hardware Hardware diagnostic program exams all socket-pin drivers before using programmer 5.5"(L) x 8.14"(W) x 1.63"(H); (140mm(L) x 207mm(W) x 41.45mm(H) Operation Voltage : 90 to 264VAC @ 47 to 63Hz (Power Consumption : 100W) CE compliant Software Features Auto Search Device Select function supports E(E)PROMs & Microcontrollers Device Insertion Test identifies improperly inserted device before programming Gang Program Mode allows programming up to 8 sockets concurrently (START ALL Key enables to program the programmers simultaneously) Checks for incorrect device insertion, backward, incorrect position, and poor pin contact. Device Operations: Read, Blank check, Program, Verify, Checksum, Data compare, Security, Auto (blank check program- verify) Option Bit program Displays programming parameters and optional bit information on the screen Sets device/buffer address ranges before programming devices User-changeable programming parameters Built-in editor for both buffer date and test vectors Supports Binary and all hex files (POF and JEDEC, Intel Hex, Motorola S Records, Tekhex, straight hex, hex-space, Extended Tekhex, and others, automatic file type recognition) with Load, Edit, and Save commands Devices Programmed M25Pxx, MX25Lxx, S25LFxx, SST25VFxxx NAND Flash Memory Samsung K9Kxxx, K5Axxx, K5Fxxx, M-System MDOC-256 / 512 / 1G / 2G, and Toshiba TC58xxx St-Micro NAND01G / 02G / 04G 28Fxxx, 29Fxxx, 38Fxxx, 29LVxxx, 26LVxxx, 29GLxxx, 29ALxxx, 29Wxxx, 36xxx, 32HFxxx, 34VFxxx, 37VFxxx, 39SFxxx, 39VFxxx, 45LFxxx, 49LFxxx, 50FWxxx 27xxx and 27Cxxx series, from 16 Kbit to 32Mbit with 8-bit/16-bit 256 Kbit to 32 Mbit 28Fxxx, 29Fxxx, 29Cxxx, 29BVxxx, 29LVxxx, 29Wxxx, 49Fxxx series (1.5, 1.8, 2.7, 3.3, 5.0, or 12 Volt) 24Cxx, 24Fxx, 25Cxx, 59Cxx, EPC1/1213/1648, and 93Cxx 27Sxx, 7Cxxx, 71xx, 74Sxx, 87Sxx, 82Sxx, ispLSI (10/20)xx, ispGAL22V10, ispGDS1(2)x, LC40(41)xx M4Axxx series PEELs 153, 173, 253, 273, 18CV8, 20CG10 series EPLDs PLCxxx, PLSxxx, PLUSxxx, Epxxx, EPCxxx, EPMxxx, PLDxxx, 5Cxxx, 85Cxxx series TSOP, BGA, QFP, TSOP2, FBGA, TQFP, CSP, uBGA, PLCC, SOIC, EBGA, PoP, SSOP, TFBGA and more System Requirements A hard disk drive (4 Megabytes) is recommended for software installation / set up PC RAM size: 512K of conventional memory OS: WINDOWS 7, 8 or 10 Standard Accessories Power Cord USB Cable Software CD User's Guide
|
